LAN9512 uboot driver (namrata_nalawade)
Hi all, I have lan9512 working in my kernel. Now , I have one requirement to detect USB in bootloader. can anyone share me the link of LAN9500 uboot driver ? regards,Namrata..
View ArticleHow to configure TFTP Linux for to charge a bootloader with TCPIP pic18...
Hi, I use microchip TCP/IP stack v5.36.4 and bootloader with pic18F ethernet family. It works perfectly with windows OS But when I do this test with linux. It does not work : I have the following...
View ArticleTCP/IP Stack with no Management Interface (morgan1361)
Hello all, I have a project that requires using the KSZ9477S with a PIC32MZ. I have everything functioning using MIIM and hardware configuration straps. The problem is that the SGMII port (port 7) will...
View ArticleRMII communication stops when unrelated pin is switched to Out (Mic)
Setup:PIC32MX795F512H => Harmony v2.06 => RMII => LAN8740A After quite a bit of hassle to get everything working fine. I tried as per advice of the datasheet to switch all remaining non-used...
View Articlefragmentation support (Witek)
Hello all,I am having problems with the TCP/IP stack and fragmentation support. PIC32MZSMSC8720Harmony 2.06 (Network presentation) I need to receive 2961 bytes from a server. In wireshark we can see...
View Articleis it possible? One receiver 50 transmitter in wireless communication? (baby)
I wish to know about the possibility of single Receiver with multiple transmitter in wireless communication?if yes means, which type of wireless communication is better?if no means , why?..
View ArticleKSZ8794CNX standalone mode not works (destmaster)
Hello,I've trouble to getting working the KSZ8794CNX in standalone unmanaged mode. I've the port 1 to 3 connected ... all the pins for port 4 (Gigabit no phy port) is unconnected. The SPI pins are...
View ArticleHow to make my device pin enable? (aatifshaikh66)
Hi all, I'm currently working on a project which is a MODBUS_TCP application, based on TCP/ IP client-server protocol. The Hardware I'm using is PIC32MZ144EFM controller with LAN9353 switch. At...
View Articlebarkeley_udp_server receive packet irregularly (chavan)
Hello allI am using PIC32MZ EF starter kit. I am using barkeley_udp_server demo example with the slight modification to receive and send packets. My starter kit is not receiving all the packets from...
View ArticleKSZ9897A Port 7 Accessible via MDIO/MDC? (Jopana)
I have a microcontroller (with an internal MAC) connected using MII to Port 7 of a KSZ9897A switch. Port 7 is configured as an external PHY, and I would like to access the PHY using the MIIM interface...
View ArticleInterfacing LAN9512 with KSZ8794 (destmaster)
On my board I've the KSZ8794 ETH switch with 2 port connected to RJ45 connector the third port is connected with USB to ETH bridge LAN9512. I use capacitive coupling to join this interface but, the KSZ...
View ArticleFTPClient PIC32 (UmbeDiGenova)
Hi,i search example for create FTP CLIENT with PIC32 Ethernet Starter kit....My application must transfer txt.file from PIC to an server FTP.Can anyone help me? Very thanksUmberto..
View ArticleStrange behavior with MAC numbers (tpicon)
Hi folks I'm struggling with a problem related to MAC. I have to 2 boards with PIC18F97J60 communicating one each other through UDP unicast. The Mac address for both is official, we bought from IEEE....
View Articlequestion on connecting differential pairs to a PHY (karatsin)
Hi! I am looking at connecting a KSZ9563RNXC switch to a couple devices in my design. One device (a system on a module) already has an ethernet PHY on the board and outputs TX/RX differential pairs...
View ArticlePort Learning (loyalfish)
Hello,Iam a bit new to ethernet so far i have built a Unmanaged switch using the KSZ9897R IC pretty simple.Iam curious is there a way the switch can determine which port on the switch the current...
View ArticleATWINC1500 replacing ENC28J60 (larrycook99)
We are working on replacing the ENC28J60 ethernet chip in a legacy PIC24 design with an ATWINC1500. The idea is that we can switch to wireless access and save code space since the WINC1500 has an...
View ArticleMTBF of KSZ8061 (melbinmanuel)
Hi all,I'm using the ethernet PHY KSZ8061 in my project. For the documentation purpose, I need to know the MTBF(Mean Time Before Failure) of the PHY. I couldn't find MTBF in the datasheet. So kindly...
View ArticleAlternet RMII ethernet PIC32MZ2048ECG100 not pinging (ASHWANI979)
Hi,I am a new user of PIC32MZ2048ECG100 and try to make firmware of barkley_tcp_server with Mplab harmony versionV2_05_01, but I did wrong in Mplab harmony device configuration setting for...
View ArticleModify MAC Address - PIC32MZ1024EFH144 (schmerse)
Dear all, I'm trying to modify the default MAC-Address to a customized one which is stored in the FRAM of my System and I can't get it running for any reason. Is there anybody who already did it...
View ArticleLooking for reference codes for LAN9250 with a PIC32MX MCU using the PMP or...
Hi microchip staff or community forum members, We are using PIC32MX795F512L PMP interface to LAN9250 through host bus interface(HBI) index mode 16-bit operation in our design. We are developing...
View Article