Hello, Is it possible to make an EhertCAT slave using a LAN9252 that the first port (ETC IN) is Ethernet and the second port (ETC OUT) is optical fiber? Thank you, Kleber...
↧
EtherCAT slave using LAN9252 with Ethernet and Optical fiber (kgouveia)
↧
PIC32MX795 512L Web server Problem (TrioX)
Hi all, Im new to this board an i have a problem with the TCPIP web server in this case.I can connect to the web server, but there are strange symbols.Testet complicated and easy web Page. Allways the same problem.I also tried to recompile and make new mp..
↧
↧
Which library is better for PIC32? (p_stoyanoff)
Greetings! I want to ask which library to choose for my TCPIP project - mla or harmony? I`m going to use PIC32MX150F128B and ENC28J60 as interface. I`m going to need TCP server and client. I want the project to be as smaller as possible because I have to ..
↧
LAN922 misses first 4 bytes of packet in some scenarios (ranshalit)
I am using LAN9221 in high secuty product.
We encounter issue in which in recieving packets,
in some sceanrios, the the recieved packet miss the first 4 bytes,
for example, instead of getting packet:
0a 1b 3c 4d 5e 6f 50 7b 9d a6 4c 39 08 06 00 01
..
↧
LAN8740A Problem (Tolotos123)
Hello, I have created a own PCB with the Ethernet Starter kit II as template.I used the "Schematic Checklist for the LAN 8740" also. Now I have Problems to get it work.I measured PIN 6( VDDCR) -> 2V. Thats too much, the datasheet says -> 1.5V max. Whats w..
↧
↧
inline statements in PIC32 (avil)
Hi, Am trying to port 32x16 RGB Display Driver from adafruit (aurdino ) to pic32 microcontroller. i have ported most of the library but stuck at some point below,the #defined one #define pew asm volatile( \
"ld __tmp_reg__, %a+" "\n\t" \
"out % , __tmp_..
↧
PIC18F4620 + Stack5.25 + RS232 (agiofelipe)
Hello everyone.I have a board with a PIC18F4620 running the tcpip stack vs 5.25 and I would like to add a serial communication to send some data.The problem is that when I remove the comment from #define STACK_USE_UART in tcpipconfig.h file the following ..
↧
How to use lan9252 Expansion Mode? (Henry_wu)
HiI configured the LAN9252 in Expansion Mode.
And chip_mode_strap=11 ,that is 3port upstream mode.The problem is that when i just use port2(DC to master) and port1(AC to next slaver S1) ,it works.While i connected another slaver S2 to port0, the S2 works..
↧
Use DMA on LAN9252 (SceUtec)
Good morning,
I need to extract (by a microcontroller) 1Kbytes of information from LAN9252 as fast as possible.
I wondered if there was a component operating mode that allowed the component to light up through the DMA of the microcontroller.
I read fro..
↧
↧
Dynamic Variables in Include Files (alanp)
Hi Guys,
I'm using 4.13 stack with dynamic variables and include files.
Is there a way to get the dynamic variables to work inside an include files. For example I have a header.inc file that has the ~name~ variable. This variable is also in the .htm..
↧
LAN9252 EEPROM PDI Access (FW Updates) (Schoon195)
Trying to update the SII (ESI File) with a FW update in my application; But from the datasheet, it doesn't look possible, at least from the PDI Side.. Notes in the datasheet say:EtherCAT controls the SII EEPROM interface if the PDI EEPROM Control bit of t..
↧
LAN9303 Port 1/2 PHY basic control register RMII access (chuchuruchu)
Dear all,I'm looking for a way to read /write PORT1,2 basic registers on LAN9303...I'm using PIC32MX675F512H, XC32 compiler v. 1.44, Harmony v. 2.04I can read/write PORT0 virtual PHY register (and all vendor register) but there is no way to access PORT 1/..
↧
Retrieving data on PIC demand from a distant server (crocu)
Hello I need to retrieve a very simple data stored into a TXT file located at distant server, ie :data.txt22.5 Could you please tell me if i could read that file and get the contents with GenericTCPClient ? I'm thinking about this way to archieve that but..
↧
↧
lan9252 3 port upstream model (Henry_wu)
Lan9252 is set as 3 port upstream model,so the external phy address must be 0. But the external phy address now is one which is same as the internal phy B address.Is it possible to configure the external address to 0 via MII (mainly mdio and mdc )..
↧
LAN8720: no reference clock at REFCLKO (Hfuhruhurr)
Hi all, we are using a custom board with a LAN8720 connected to an NXP LPC1768 MCU.We want to use RMII, provide 25 MHz through a crystal oscillator on XTAL1 and 2 and pass the REFCLKO 50 MHz signal to the MCU.However, I don't see any output on the referen..
↧
MIB2BIB failure? (Dag)
I am having difficulty compiling the snmp.mib sample file from Microchip using the mib2bib.exe utilityNo File is created and no error output of any kind.
D:\tmp>mib2bib snmp.mib
mib2bib v1.0.1 (Oct 14 2003)
Copyright (c) 2003 Microchip Tec..
D:\tmp>mib2bib snmp.mib
mib2bib v1.0.1 (Oct 14 2003)
Copyright (c) 2003 Microchip Tec..
↧
ENC28J60 + PIC24F (Chazz)
Good day!!! I would like to start using the enc28j60 together with a pic24f but I do not know where to start, if someone could tell me where to get an example or something that could serve me would be very grateful. Thank you so much!!..
↧
↧
KSZ8794/8795 driver and VLAN configuration (burebius)
Hello! First of all I have to say I'm not that good with either English language (not really my native) or switching devices and networks, so much patience is appreciated. 1. I'd be rather thanksful for you to look through my thoughts on the problem.
I h..
↧
INTEnableSystemMultiVectoredInt() is where (pjakrishnan)
I have successfully built and run with debug the TCPIP Stack Demo App from microchip_solutions_v2013-06-15 on my PIC32SK board with PIC32MX360F512L, on Explorer16 with ENC28J60 Ethernet PICTAil Plus Daughter card(yes, legacy stuff). AND, I had to stick to..
↧
PIC18F67J60 Ethernet firmware (KMDN)
I am looking for Ethernet firmware for PIC18F67J60 controller..
↧