VSC6803 with PHY VSC8489 (pgainbedd)
Hi, the server always kicks me out, so I will create this step by step.I have a PHY VSC8489 connected to a ARM Cortex 3 via I2C.I found out that VSC6803 is interesting for using an appropriate API with...
View ArticleUDP communication with pic32mz starter kit and ksz8061 (marco95)
Hi guys I'm very sorry te repost the question, but maybe I selected the wrong place before. I will be very grateful if you can help me with this issue https://www.microchip.com..ums/m/tm.aspx?m=1188456...
View ArticleCapacitive coupling (Resh_Shar)
Hi, In our design we have used LAN9253 and KSZ8863RLLI part,we planned to use PHY to RJ45 capacitive coupling.Will capacitive coupling work for LAN9253 and KSZ8863RLLI?Any special care we need to take...
View ArticleDP83848 PHY Driver - Harmony 3 (XorLor)
The PHY driver for DP83848 doesn't seem to be supported yet in Harmony 3. Has anyone been able to get it working? If so, what steps did you take? Processor: PIC32MZ1024EFG100 The hardware works well...
View ArticleSoftware command/tool to test KSZ8081 Phy Loopback test (noufalp)
Hi, We are using SAMA5D2 SOM1 EK SOC in one of our porject where KSZ8081 PHY chip used is for ethernet . We would like to perform the PHY Digital(local) loopback test on the device as mentioned in the...
View ArticleRequest for process to enable/disable HSR mode of KSZ9477S via sysfs entries...
Hi, We are using KSZ9477S Network switch, please find the complete product description and linux driver details from the below mentioned links. KSZ9477S product details:...
View ArticleENC28J60 no clockout (varesa)
I am unable to get anything on the CLKOUT pin (chip not running/starting?). Can anyone see what is wrong in my setup? I am clocking it from a 25MHz oscillator, verified working & present on pin 23...
View Articlelan9303 PHY ID and Number (voloviq)
Can someone write me what is ID and Number of LAN9303. I check in documentation and documentation says 0007.C0D1. Unfortunately, this ID and Number is exactly the same as for LAN911x. When I use...
View ArticleLAN7800 implementation for data transmission: is the better option? (juanma_Cab)
Hi everyone, I'm working on a design with Raspberry Compute Module 4 using ethernet lines from this device. I want to create video data transmission through these ethernet lines and then convert them...
View ArticleLAN7800 implementation for data transmission: is the better option? (juanma_Cab)
Hi everyone, I'm working on a design with Raspberry Compute Module 4 using ethernet lines from this device. I want to create video data transmission through these ethernet lines and then convert them...
View Article[ENC28J60] INT Never Resets (markthumes@gmail.com)
Background:I've used MPLAB's MCC tool to configure my project with the TCP/IP Lite stack. I have moved the ETH_EventHandler outside of the NetworkManage() function, and into an ISR. Issue:I can ping...
View Article[MCC - TCP/IP Lite] Incorrect Generated Code - Packet Interrupt Flag Clear...
I'm not sure if this is a manual vs software issue, but the ENC28J60 manual states that the Receive Packet Pending Interrupt Flag (PKTIF) bit in the ETHERNET INTERRUPT REQUEST (EIR) (FLAG) REGISTER is...
View ArticleLAN9253 redundancy (michele sponchiado)
Hi, we are a company working on a project where redundancy is wanted on the EtherCAT slave bus access, i.e. we are looking for a system where the data coming from the EtherCAT are processed in parallel...
View ArticleTAG KSZ on x86 Linux (mateusz28)
Hi, We are trying to achieve a manageable switch configuration on x86 architecture. In our setup, we are using a Microchip LAN7431 chip on the PCI bus with KSZ9893RNXI connected through RGMII. Port 1...
View ArticleWrong signal names in KSZ9893R datasheet? (Mickepick)
Hello!I need to read out register 0x0210 (LED Strap-In Register), documented on page 67 of DS00002420D.This register is 32 bit wide, where the lowest four bits contain the following data (other bits...
View ArticleKSZ9897 direct connection RGMII (JakubLab)
Hello. I would like to know if it is possible to connect two KSZ9897 via RGMII? I found document with other KSZ that shows that is possible...
View ArticleUse PIC32/UDP to send Audio over Ethernet? (rbuck)
A little over a year ago I used a PIC16F1718 and this module:https://www.usriot.com/products/serial-ttl-to-ethernet-module.htmlto send audio over the Internet from one building to another. I used UDP...
View ArticleLAN9250 not working (swanand)
Hi all, i am working on LAN9250 with stm32l073 micro-controller over SPI. i found one example code of interfacing LAN9250 with PIC controller here and with reference to that i have written the code for...
View ArticleMAIN APPLICATION TCP IP STACK NOT GETTING INITIALIZED WHEN BOOTLOADER JUMPS ....
Hello Everyone,I am using PIC32MZ1024EFM144 and have developed bootloader and application for OTA , so bootloader is able to jump on app and all peripherals are working fine , but the issue is when I...
View ArticleKSZ9031 local loopback problem (fcg)
Hello, I'm trying to test KSZ9031 in local loopback mode. For this purpose I use Boundary scan tool on Xilinx fpga. According to datasheet "For 10/100 Mbps loopback, 1. Set Register 0h, - Bit = 1 //...
View Article